PTP 650S

Wide-band operation 4.9 to 6.05 GHz (allowable frequencies and bands are dictated by individual country regulations. The most common bands are listed here.) 4.940 – 4.990 GHz (Public safety) 5.15 – 5.25 GHz 5.25 – 5.35 GHz 5.470 – 5.725 GHz 5.725 – 5.850 GHz 5.825 – 6.050 GHz 2.5 – 2.6 GHz3 3. .3 – 3.6 GHz3

5, 10, 15, 20, 30, 40, and 45 MHz channels Channel sizes depend on individual country regulations

10 bps/Hz maximum

By dynamic spectrum optimization or manual intervention; Automatic selection on start-up and continual self-optimization to avoid interference

Up to 27 dbm at bPsK; up to 23 dbm at 256 QaM

Integrated: Up to 160 db with 20 MHz channel and integrated 19 dbi antenna; Varies with modulation mode, Channel size and spectrum

-98 dbm with 5 MHz channel

Fast Preemptive adaptive Modulation featuring 13 modulation / FeC coding levels ranging from bPsK to 256 QaM dual payload MiMo

Synchronized Time division duplex (Tdd) and Half duplex Frequency division duplex (Hd-Fdd); dynamic or fixed transmit/receive ratio; each Tdd-synchronized link requires a Cambium Tdd-synC synchronization unit5 to provide an accurate timing reference signal

Integrated: Flat panel – 19 dbi

Software limited to 1.25 miles (2.0km); optional software license key to enable long-range applications

FiPs-197 compliant 128/256-bit aes encryption (optional) HTTPs and snMPv3 Identity-based user accounts Configurable password rules User authentication and Radius support Event logging and management; optional logging via syslog disaster recovery and vulnerability management

IEEE 802.3

Dynamically variable up to 450 Mbps Maximum conditions – 2x2, 45 MHz channel1, 256 QaM

1 – 3 ms one-direction latency

8 Queues

Layer 2 and layer 3 ieee 802.1p, MPls, ethernet priority

Line rate ( >850K packets per second)

Synchronous ethernet; IEEE 1588v2

Jumbo frame up to 9600 bytes

2x Gigabit ethernet copper ports: Gigabit Port 1: data + Poe power input Gigabit Port 2: 802.3at Poe output port (optional) sFP port (single-mode fiber, multi-mode fiber, and copper Gigabit ethernet options available)

8 x T1/e1 TdM module (optional indoor unit)3 G.823-compliant timing dC power input (compatible with aC+dC Power injector output)

1 to 3 ms typical depending on range, bandwidth, modulation mode and number of T1/e1 ports; Accurate T1/e1 latency figures can be determined for any given configuration using the Cambium PTP linKPlanner

Power status, ethernet link status, and activity on extended Range Poe supply

In-band and out-of-band management (oobM)3

iPv6/iPv4 dual-stack management support Web access via browser using HTTP or HTTPs/Tls4 snMP v1, v2c and v3, Mib-ii and proprietary PTP Mib Cambium Wireless Manager, WM 4.0/sP4 or higher online spectrum analyzer (no impact on payload traffic or network operation)

Built-in audio and graphical assistance for link optimization

Distance between outdoor unit and primary network connection: up to 330 feet (100 meters) using Power-over-Gigabit ethernet; longer distances up to 984 feet (300 meters) can be achieved using fiber interface

Integrated outdoor unit (odu): Width 207mm (8.2”), Height 306mm (12.0”), depth 69mm (2.7”): Weight integrated odu: 4.1 kg (8.95 lbs) including bracket operating temperature -40° to +140° F (-40° to +60° C), including solar radiation dust-water intrusion protection iP66 and iP67

200 mph (322 kph)

Two options: aC power injector: 32° to 104° F (0° to +40° C); 35 W; 90-240 vaC, 50/60 Hz dimensions: Width 5.2” (132mm), Height 1.4” (36mm), depth 2” (51mm) aC + dC power injector: -40° to 140° F (-40° to +60° C); 70 W; 90-240 vaC, 50/60 Hz dimensions: Width 9.75” (250 mm), Height 1.5” (40 mm), depth 3” (80 mm)

30 W maximum

ul60950-1; ieC60950-1; en60950-1; Csa-C22.2 no. 60950-1; Cb approval for Global

-4.9 GHz: FCC Part 90y, Rss-111 5.x GHz: FCC Part 15, sub-parts 15C and 15e; Rss 210 issue 8; en 302 502; en 301 893 eire ComReg 02/71R1, uK approval to iR2007

Europe – en 301 489-1 and -4